thank you very much for choosing a noctua cooler. this manual will guide you through the installation process step by step. noctua LGA775 mounting-kit installation manual nh-u12p-LGA775 | installation manual required mounting parts (from the LGA775-bag): the backplates screw sockets with the mainboards screw - holes. step 3: attaching the fastening brackets to the heatsink now screw the mounting bars to the backplate using small screws and washers. tightly screw the fastening brackets to the base of the heatsink using 4 short screws. step 4: applying thermal paste if there are residual traces of thermal paste or thermal pads on your cpu, please clean them off first. removing the mainboard step 1: in case you want to use the nh-u12p on an assembled system, you first have to remove the mainboard from the case as the cooler has to be screwed together with the backplate on the back side of the mainboard. 1x lga backplate prior to installing the cooler, please consult the compat - ibility list on our website and verify that the cooler is fully compatible with your motherboard. should you encounter any difficulties, please check the faqs on our website and dont hesitate to contact our support team at support@noctua.at . noctua cannot be held responsible for any damage or losses caused by compatibility issues. multilingual versions of this manual are available on our website: www.noctua.at 2x short silver springscrews 2x short mounting bars required mounting parts (from the common parts bag): 2x standard fastening brackets 2x red, thin washers 2x pressure springs 8x short screws press a small drop (4-5mm diameter) of nt-h1 onto the cen - tre of the heat-spreader. put the heatsink onto the cpu and turn it back and forth a few times in order to spread the paste. caution: peel off the protection film at the bottom side of the heatsink first! caution: applying too much thermal paste will lower the heat conductivity and cooling performance! caution: the rubber foam square of the lga backplate has to face the mainboard. dont remove the white protec- tion film! caution: dont forget to put 4 washers between the mainboard and the mount - ing bars to avoid damage to the mainboard. step 2: attaching the backplate place the backplate on the back side of the mainboard, aligning orientation a orientation b choose the alignment of the mounting bars according to the desired final orientation of the cooler: caution: make sure that the straight sides of the mounting bars face the socket and the bulgings are pointing outwards.
nh-u12p-LGA775 | installation manual attaching the fan step 6: first stick the 2 anti-vibration strips onto the cooling fins in order to dampen minor vibrations emitted by the fan. align the mounting holes of the fastening brackets with those of the mounting bars. now screw the fastening brackets to the mounting bars employing the pressure springs and the respec - tive screws caution: tighten the screws until they stop. step 5: attaching the heatsink to the cpu even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely. therefore, we aim at providing the highest possible level of dependability and convenience by offering a warranty period of 72 months and direct, fast and straightforward rma service. in case of warranty, you can either request rma at your retailer or use our direct rma service. for further information, please consult www.noctua.at. in order to process your rma enquiry, we need a proof of purchase, so please dont forget to keep your invoice! please also note that any modifications to the cooler, fan or mounting parts will void your warranty. warranty for all enquiries concerning your noctua cooler, both your retailer and the international noctua support team at support@noctua.at are at your service. please also consult the faq section on our website www.noctua.at. support & faqs connect the fan to the mainboard, power supply or fan con - troller. depending on your cpu and the temperature inside the case, you may interconnect the supplied ultra-low-noise adapter (u.l.n.a.) in order to further reduce the fans operat - ing noise. caution: when using the u.l.n.a., check the temperature of your cpu using appropriate software (e.g. the respective ap - plications of your mainboard manufacturer), in order to evade automatic throttling of the cpu due to the increased tempera - ture. if the cooling performance is insufficient, please increase case ventilation or remove the u.l.n.a. then attach the fan to the heatsink using the 2 steel clips, placing it so that it blows onto the heatsink (you can optionally use the second pair of clips to install a second fan).
thank you very much for choosing a noctua cooler. this manual will guide you through the installation process step by step. noctua am2(+) mounting-kit installation manual step 2: nh-u12p-am2(+) | installation manual required mounting parts (from the am2(+)-bag): attaching the backplate place the backplate on the back side of the mainboard, aligning the backplates screw sockets with the mainboards screwholes. put the 4 white, thin washers under the mounting bars and the 4 red, thick washers onto the mounting bars. now screw the mounting bars to the backplate using the small screws with higher thread-pitch (from the am2(+) bag). step 3: attaching the fastening brackets to the heatsink choose the fastening brackets according to the desired orienta - tion of the cooler: when using the 90 fastening brackets, first stick the spring screws and springs into the fastening brackets. then screw them to the copper base of the heatsink tightly using 4 short screws. step 4: applying thermal paste if there are residual traces of thermal paste or thermal pads on your cpu, please clean them off first. 2x mid-sized silver springscrews caution: make sure that the bulgings of the mounting bars are pointing towards the socket. 4x short screws with higher thread pitch removing the mainboard and retention module step 1: in case you want to use the nh-u12p on an assembled system, you first have to remove the mainboard from the case as the cooler has to be screwed together with the backplate on the back side of the mainboard. if your mainboard uses a retention module for cpu cooler installation, you have to remove it first. should you experience any difficulties, please consult your mainboards manual. if your previous cpu cooler is attached using a different mounting mechanism, please remove it according to its manual. 1x am2(+) backplate 2x short mounting bars prior to installing the cooler, please consult the compat - ibility list on our website and verify that the cooler is fully compatible with your motherboard. should you encounter any difficulties, please check the faqs on our website and dont hesitate to contact our support team at support@noctua.at . noctua cannot be held responsible for any damage or losses caused by compatibility issues. multilingual versions of this manual are available on our website: www.noctua.at required mounting parts (from the common parts bag): 2x 90 fastening brackets 2x standard fastening brackets 4x white, thin washers 4x red, thick washers 2x pressure springs 4x short silver screws for fastening brackets press a small drop (4-5mm diameter) of nt-h1 onto the cen - tre of the heat-spreader. put the heatsink onto the cpu and turn it back and forth a few times in order to spread the paste. when using the standard fastening brackets, tightly screw them to the copper base of the heatsink using 4 short screws. caution: peel off the protection film at the bottom side of the heatsink first! caution: applying too much thermal paste will lower the heat conductivity and cooling performance!
nh-u12p-am2(+) | installation manual attaching the fan step 6: first stick the 2 anti-vibration strips onto the cooling fins in order to dampen minor vibrations emitted by the fan. now screw the fastening brackets to the mounting bars em - ploying the pressure springs and the respective screws. when employing the 90 fastening brackets, please use the supplied mounting-tool to tighten the springscrews. caution: tighten the screws until they stop. align the mounting holes of the fastening brackets with those of the mounting bars. step 5: attaching the heatsink to the cpu connect the fan to the mainboard, power supply or fan con - troller. depending on your cpu and the temperature inside the case, you may interconnect the supplied ultra-low-noise adapter (u.l.n.a.) in order to further reduce the fans operat - ing noise. caution: when using the u.l.n.a., check the temperature of your cpu using appropriate software (e.g. the respective ap - plications of your mainboard manufacturer), in order to evade automatic throttling of the cpu due to the increased tempera - ture. if the cooling performance is insufficient, please increase case ventilation or remove the u.l.n.a. even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely. therefore, we aim at providing the highest possible level of dependability and convenience by offering a warranty period of 72 months and direct, fast and straightforward rma service. in case of warranty, you can either request rma at your retailer or use our direct rma service. for further information, please consult www.noctua.at. in order to process your rma enquiry, we need a proof of purchase, so please dont forget to keep your invoice! please also note that any modifications to the cooler, fan or mounting parts will void your warranty. warranty for all enquiries concerning your noctua cooler, both your retailer and the international noctua support team at support@noctua.at are at your service. please also consult the faq section on our website www.noctua.at. support & faqs then attach the fan to the heatsink using the 2 steel clips, placing it so that it blows onto the heatsink (you can optionally use the second pair of clips to install a second fan).
|
